By Ed Sullivan
The latest in automated lubrication systems ensure optimum equipment performance — even in demanding pharmaceutical manufacturing environments — and reduce unscheduled maintenance.
Corrosive plant environments are among the most serious threats to many industries today, contributing to extensive production downtime and exorbitant maintenance costs.
According to a G2MT Laboratories report, the annual cost of corrosion for the U.S. industrial market was expected to reach over $500 billion in 2015. This estimate is based on the most recent NACE (National Association of Corrosion Engineers) study, adjusted for inflation.
Among the most devastating effects of corrosion is its destructive impact on the load bearing surfaces of plant equipment, which are supported by many types of bearing components such as rollers, spines, gears, ball bearings or other moving parts. Unless these components are provided proper lubrication, they will be subjected to excessive heat and wear, both leading to premature failure.
With pharmaceutical manufacturing equipment running at higher speeds and longer periods, it is more important than ever to ensure that lubrication systems are providing bearing devices with efficient, timely applications of lubricating oil or grease in order to ensure wear life, safe operation, reduced unscheduled downtime of processing machinery, and more economical operating costs. For that reason, many manufacturers are opting for automating their lubrication systems.
The multi-point challenge
Many pharmaceutical manufacturing and related operations have hundreds, even thousands of lubrication points in a single facility. Although automatic lubrication systems have been around for decades, much of this work is still conducted using manual labor – particularly when the lubricant is grease.
While the pharmaceutical industry is continually moving to higher-speed, higher-volume automated equipment, it is becoming increasingly impractical for the industry to depend on labor-intensive, point-by-point, manual lubrication.
“Bearing giant SKF has estimated that 57 percent of all bearing failures are lubrication-related,” explains Richard Hanley, president of Lubrication Scientifics (Irvine, CA). “That failure rate can be reduced dramatically by automating the lubrication process, which ensures that the right amount and type of lubrication are delivered to every equipment bearing point.”
Lubrication Scientifics engineers and manufactures a variety of automated lubrication systems and components that are installed on equipment used in a wide variety of industries in addition to pharmaceuticals, including the food processing, pulp & paper, chemical processing, steel, petrochemical and mining industries.
From an economic point of view, the payback period for most of these systems is less than a year. In some cases, engineered lubrication systems with advanced monitoring capabilities can easily save elaborate processes millions of dollars in downtime costs per year. One less failure could easily pay back a $10 thousand system. Today’s automated systems use 33 percent less grease and can also provide additional reductions in operating costs, such as energy, environmental disposal, labor, and workman’s comp insurance.
Installing an automated lubrication system that dispenses the right amount of appropriate lubricants at proper intervals is a vital requirement in the pharmaceutical industry, ranging from applications such as tableting, conveyors and packaging equipment.
It is quite a challenge for many automated systems to supply the right amount of lubricants to bearing points because, in many instances, the high-speed equipment used by pharmaceutical manufacturers operates with optimum performance when very small amounts of lubricants are required. When larger amounts are dispensed, there is the risk that some lubricant will overflow the bearings and contaminate a cleanroom environment. Supplying smaller amounts of lubricants at closer intervals not only solves that problem, but can also lower energy costs by enabling the equipment to run with less friction.
For this reason Lubrication Scientifics has developed an automated stainless steel system that allows operators to dispense as little as 0.0015 cubic in. of lubricant to each bearing point – 70% less than other comparable devices.
Harsh production environments
Pharmaceutical processing plants are exposed to some of the harshest environmental factors, including extreme room temperatures and mandatory wash-down procedures that may occur at frequent intervals.
FDA, 21CFR110.35 requires that all processing lines and equipment be adequately sanitized, as often as necessary. This requirement is typically met by a full equipment wash down, with an approved cleaning agent. These wash-downs create serious corrosion problems for any non-stainless steel components used in the processing line.
Corrosive damage from exposure to caustic wash-down fluids can severely compromise the performance and service life of lubricating system metering valves - the valves that dispense oil or grease in controlled proportions to each connected lube point - which are constructed of zinc- or nickel-plated carbon steel.
“In such an environment, the corrosion resistant life of a plated carbon steel metering valve or system component will only be weeks to months,” Hanley says. “Although the initial corrosion will look much like rust, it will eventually cause the lubrication metering valve to lose its effectiveness long before normal wear and tear would compromise that part.”
In the pharmaceutical manufacturing industry, corrosion problems are normally prevented through the use of equipment made of stainless steel. However, as a broad offering of stainless steel metering valves has not been readily unavailable, the only effective anti-corrosion solution for automatic lubrication system components has been to enclose the plated carbon steel metering valves into stainless steel enclosures. Including the cost of the enclosure, the bulkhead fittings, and the installation labor, it is easy to spend $2,000 to protect a $500 hundred dollar plated carbon steel metering valve. Yet, the space required to mount such as enclosure may not be available on or near the processing line.
In such cases the installation metering devices made of stainless steel that can be mounted directly to the plant equipment is the most cost effective solution to maintaining sanitary standards and insuring long-term production reliability. Typically, stainless steel metering valves such as those offered by Lubrication Scientifics cost between 1-1/2 and 3 times the price of a carbon steel-plated metering valve. Still, this is typically 40% to 60% less expensive than enclosing plated carbon steel valves in a stainless steel enclosure.
Automated system basics
There are several different types of automated lubrication systems, but a typical system consists of controller/timer, pump with reservoir, supply line, metering valves and feed lines.
Whatever the design, automated lubrication system metering valves must stand up to the rigors of harsh plant environments.
One of the most common lubrication systems is the Single-Line Parallel, which is also referred to as the Injector-type of lubrication delivery methodology. This system is known for its ease of installation, adjustable metering of valves (or injectors) and applicability to a minimum of one and maximum of six lube points per device. Lubrication points may be added or removed without redesign of the system. On the down side, it is difficult to verify that each lubrication point is constantly being serviced.
Another common system is the Dual-Line Parallel. This system is also easy to install and features adjustable metering valves. With this type of system a minimum of one and maximum of eight lube points may be serviced from each device, and lubrication points may be added or subtracted without system redesign. Also, heavy greases may be delivered over very long distances. However, with this system it is difficult to verify that each lubrication point is constantly being serviced.
A third type of automated system, the Single-Line Progressive System (aka the Divider Valve System), is precisely engineered to deliver exact lubricant requirements to each point. However, with this system, lubrication amounts and points may not be altered, and initial installation costs are higher than with other systems. A primary advantage of these systems is that system performance can be easily and inexpensively monitored to verify that each lube point is constantly being serviced.
In order to overcome the various threats of corrosive and caustic environments, Lubrication Scientifics makes all three types of system and components available in 303 and 316 stainless steel, most of which are available within days rather than months.
Verifiable system advantages
Plants that have the verifiable automated system normally have the need to deliver precise amounts of lubrication to many points. This requirement is so stringent that is critical that workers could not normally adjust the amount or type of lubricant that being delivered to the equipment.
The biggest advantage of the Single-Line Progressive type of system is that every lubrication point is monitored, ensuring that each point is receiving the proper lubrication, thereby maximizing production uptime.
In addition, this type of system prevents unauthorized interference with system settings, so that workers cannot inadvertently change the precise amounts and intervals of lubrication sent to various points.
About The Author
Ed Sullivan is a Hermosa Beach, CA-based writer. He has researched and written about high technologies, healthcare, finance, and real estate for over 25 years.
For more information, contact Lubrication Scientifics, LLC, 17651 Armstrong Avenue, Irvine, CA 92614; Phone: 877-452-0157; Email: email@example.com or visit the web site: www.lubricationscientifics.com